search

Bewator BC615 User Manual Page 3

  • Download
  • Add to my manuals
  • Print
  • Page
    / 10
  • Table of contents
  • BOOKMARKS
    • Rated. / 5. Based on customer reviews
Page view 2
ENGLISH
Installation
Tx 17 2 32
18 1 23
21 5 75
Rx
ENAB
DTR
0V
RS232
Connection to PC
Wall
socket
9-pin
D-sub
25-pin
D-sub
Tx 17 2 32
18 1 23
21 5 75
Rx
ENAB
DTR
0V
RS232
Connection to PC
Wall
socket
9-pin
D-sub
25-pin
D-sub
1 2 3 4 5 6 7 8 9
10
11
12
13
14
15
16
17
18
19
20
21
12-30V
LOCK
EXT
INT
SW1
N/W
S/A
LINK OUT
DOOR CON
BACK
LIGHT
ALERT
DUR
TAM
TAM
Tx
Rx
ENAB
DTR
0V
RS-232
EXIT
BUT
DOOR
CONT
RDR
INH
0V
2
3
5
IF2
A
B
C D
E
F
G
H
I
J
K
L
M
N
O
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
12-30V
LOCK
EXT
INT
SW1
N/W
S/A
LINK OUT
DOOR CON
BACK
LIGHT
ALERT
DUR
TAM
TAM
Tx
Rx
ENAB
DTR
0V
RS-232
EXIT
BUT
DOOR
CONT
RDR
INH
0V
2
3
5
IF2
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
A
Electric locking device. Dashed line shows con-
nection to locks with power to lock operation.
B
Power in, terminal block nos. 1 and 2.
BC615Cotag/EM: 12 – 35 VDC.
BC615: 8 - 24 VAC or 10 – 35 VDC.
C
Exit request button. To operate, short terminal
nos. 6 and 9.
D
Input for door monitor contact. Link out by jumper
F if not used. The contact should be closed when
the door is closed.
E
Input for reader inhibit. To operate, short terminal
nos. 8 and 9. The red LED on the reader flashes.
F
Place jumper if door monitor contacts are not
used.
G
Alarm set input (red LED lit). Terminal no 11 “+”,
no 12 “–”.
H
Alert output. Use an E7 relay. Connect between
terminal nos. 13 and + (10). Activated when a door
is forced open or following door release + door
held warning time and when door contacts are not
closed.
I
Duress output. Used for activating an external
alarm. Use an E7 relay. Connect between terminal
nos. 14 and + (10).
J
Tamper switch. Normally closed when the housing
is closed.
K
Connection to printer. For connection to PC, see
the diagram. RS232 interface: 9 600 bps, no par-
ity, 8 bits, 1 start bit, 1 stop bit
L
If the card reader is used with Bewator Entro sys-
tem, attach jumper to N/W (network), otherwise to
S/A (standalone).
M
Remove jumper if backlighting is not required.
N
The SW1 push button. Used when erasing the
memory and setting a new password.
O
If the card reader is part of a Bewator Entro sys-
tem, place jumper on INT (attempts of tamper will
be displayed as messages on the PC’s screen),
otherwise to EXT. (Direct connection to external
alarm)
Page view 2
1 2 3 4 5 6 7 8 9 10

Comments to this Manuals

No comments
Related products and manuals for Card readers Bewator BC615
Card readers Bewator BC610 User's Guide   (72 pages)
Card readers Bewator BC615EM User Manual   (64 pages)
Card readers Bewator BC615 User Manual   (2 pages)
  • Meister Datamax O'Neil Dallas Evolve Communications Fiskars
  • Marantz Receiver AudioSource Audio amplifiers IHome Bluetooth music receivers Panasonic Drive recorders Lumiscope Unknown
  • Roland HP203 Makita BDF343 Gentex 7139CS-W Acer Aspire 5500Z LG DC476X
  • Samsung C49J890DKU User Manual Asus ASMB3-IKVM Specifications The Singing Machine iSM-1010 User Manual Hobart HL200 User Manual Bosch DWW06W450B Instruction Manual